GuangDong Advanced Thermoplastic Polymer Technology Co., Ltd.
GuangDong Advanced Thermoplastic Polymer Technology Co., Ltd.

Anti-static TPEs

Anti-static TPEs

UV-resistant and Anti-static Solutions

Application fields: the wire and optical cables with the requirements of UV-resistant and anti-static to the sheathing materials and needing to pass the UL VW-1 test.Product features:

1. Excellent UV-resistant property, after irradiated for 168 hours in the QUV testing box, ΔE<1. The testing parameters are as follows:

Irradiance: 0.35W/m2; illumination: 4 hours illumination(UVA 340nm), 60℃ temperature; Condensation: 4 hours condensation, 50℃ temperature: The total time: 168 hours.

2. A long-term and stabilized anti-static property with the surface resistance reaching up to108Ω/square, and it can realize the matching of various kinds of colors;

3. The two properties above can either reach the standard simultaneously or be achieved respectively;

4. Mechanical property: in support of the wire to pass every item corresponding test of UL1581/758/62 and the non-migration test, standout elasticity;

5. Temperature resistant rate: in support of the wire to pass the UL 80℃/105℃ jacket test;

6. The flame rating: UL 94 V0 vertical burning, in full support of the wire to pass the UL VW-1 and CSA FT-4;

7. Appearance: comfortable and smooth, well-distributed exquisite; excellent wear-resistant property; providing glossy, semi-matte, and matte surface products for selection;

8. Excellent processing efficiency and property, not only just using PVC screw machine, it can realize the productive efficiency of forty to eighty meters per minute, but also appears very few imperfections in during processing such as salivation, particles, bumps, and pocking marks, etc.

Technical Data of Anti-static TPEs

Technical Data SheetModel

Material Properties
Test Standard
Test Condition
General Characteristics
Material Category
Physical CharacteristicsHardnessISO 4815SShore A86
ProportionISO 1183-g/cm³1.126
Melt IndexISO 1133-1:2011190℃/2.16kgg/10min0.1
Brittle TemperatureISO 812-
Mechanical Properties
Tensile StrengthISO37:2017200mm/minMpa10.26
Tearing StrengthISO34-1:2015500mm/minKN/m
Hot Air AgingElongation Retention RateISO37:2017-%
Tensile Strength Retention RateISO37:2017-%
Electrical Performance
Volume ResistivityASTM D257-Ohm-cm
PermittivityASTM D150--
Combustion PerformanceVertical Burning TestUL 943.0/6.0mm-
Oxygen IndexASTM D2863-%

Key Benefits of Anti-static TPEs

Key Benefits of Anti-static TPEs

· Competitive price      · Respond immediately      · Strong R&D capability      · Excellent after-sales service

Please fill in the below informations if you have any questions or doubts, ATP Polymer will contact within 24 hours.
Contact No
Product type
Application type
Enquiry Message
Anti-static TPEs

ATP Polymer News Recommendation

08 Sep, 2022
About Thermoplastic Rubber
Ⅰ. How is thermoplastic rubber formed?Thermoplastic rubber is a new type of material that can be plasticized at high temperature and can show rubber elasticity at low temperature.Such materials have ...
22 Aug, 2022
Why is Thermoplastic Rubber TPV Easy to Agglomerate?
Ⅰ. Usually thermoplastic rubber elastomers are easier to agglomerate, and the reasons for agglomeration are as follows:1. If the hardness is too low, such as materials close to 0 degrees, it is usual...
15 Aug, 2022
What Should Be Paid Attention to Before Thermoplastic Rubber Injection Molding Process?
1. The barrel needs to be cleaned before thermoplastic rubber injection moldingBefore the newly purchased injection molding machine is used, or when the product needs to be changed, the raw material i...
08 Aug, 2022
Filling, Packing and Cooling of Thermoplastic Rubber Injection Moulds
Ⅰ. Filling of thermoplastic rubber injection molding process moldsIn the process of molding and filling the mold cavity, if the filling performance of the product is not good, the pressure drop is to...
01 Aug, 2022
Type Analysis of Thermoplastic Rubbers
Thermoplastic rubber transcends the traditional boundaries of rubber and plastic in industrial production, and brings new changes to the development of the rubber industry. The emerging thermoplastic ...
22 Jul, 2022
TPV Blow Molding Guide for Thermoplastic Rubber
Thermoplastic polyolefin elastomer based on EPDM+PP, material hardness: Shore A92±3; it can be molded like thermoplastics, such as polyethylene, polypropylene, etc., by injection molding, extrusion, ...