GuangDong Advanced Thermoplastic Polymer Technology Co., Ltd.
GuangDong Advanced Thermoplastic Polymer Technology Co., Ltd.

Anti-static TPO

Anti-static TPO

The modification of ATP for polyolefin elastomers mainly reflects the following technical characteristics:

1. Improved Low-temperature Resistance:

In the application of cable insulant, the modification TPO of ATP can not only meet the requirement of electric performance from the insulant but also display a more broad temperature resistant character——displaying excellent mechanical properties and aging properties at the test temperature of -50℃—+125℃. So, this is the optimized insulant for wires and cables which have special requirements for low-temperature resistance.

2. Improved shrinkage resistance:

The jacket made up of TPO wire and cable insulant from ATP keeps its section surface smooth and orderly with little retraction rate after immersing in solder machine (350℃/2"). In the application of high-temperature-resistant cables (temperature≤125℃) such as charging vehicle cables (EV Cable), equipment connection cables, etc., the jacket made up of TPO wire and cable insulant from ATP takes the place of XLPE materials to meet the requirements of insulant high-temperature aging and shrinkage for nominal cables. And this can simplify the processing procedures by a large margin and improve the processing efficiency and yield.

Application: TPO has the characteristics of small specific gravity, good impact strength, and low-temperature brittleness, and is suitable for applications in the cable industry.

Technical Data of Anti-static TPO

Technical Data SheetModel

Material Properties
Test Standard
Test Condition
Unit

General Characteristics
Material Category
---
Appearance(Light/Semi-matte/Frosted)---
Extrusion/Injection
---
Physical CharacteristicsHardnessISO 4815SShore A
ProportionISO 1183-g/cm³
Melt IndexISO 1133-1:2011190℃/2.16kgg/10min
Brittle TemperatureISO 812-
Mechanical Properties
ElongationISO37:2017200mm/min%
Tensile StrengthISO37:2017200mm/minMpa
Tearing StrengthISO34-1:2015500mm/minKN/m
Hot Air AgingElongation Retention RateISO37:2017-%
Tensile Strength Retention RateISO37:2017-%
Electrical Performance
Volume ResistivityASTM D257-Ohm-cm
PermittivityASTM D150--
Combustion PerformanceVertical Burning TestUL 943.0/6.0mm-
Oxygen IndexASTM D2863-%
Feature


Key Benefits of Anti-static TPO

Key Benefits of Anti-static TPO

· Competitive price      · Respond immediately      · Strong R&D capability      · Excellent after-sales service

Inquiry
Please fill in the below informations if you have any questions or doubts, ATP Polymer will contact within 24 hours.
Name
Email
Contact No
Country
Product type
Application type
Enquiry Message
Anti-static TPO

ATP Polymer News Recommendation

08 Sep, 2022
About Thermoplastic Rubber
Ⅰ. How is thermoplastic rubber formed?Thermoplastic rubber is a new type of material that can be plasticized at high temperature and can show rubber elasticity at low temperature.Such materials have ...
22 Aug, 2022
Why is Thermoplastic Rubber TPV Easy to Agglomerate?
Ⅰ. Usually thermoplastic rubber elastomers are easier to agglomerate, and the reasons for agglomeration are as follows:1. If the hardness is too low, such as materials close to 0 degrees, it is usual...
15 Aug, 2022
What Should Be Paid Attention to Before Thermoplastic Rubber Injection Molding Process?
1. The barrel needs to be cleaned before thermoplastic rubber injection moldingBefore the newly purchased injection molding machine is used, or when the product needs to be changed, the raw material i...
08 Aug, 2022
Filling, Packing and Cooling of Thermoplastic Rubber Injection Moulds
Ⅰ. Filling of thermoplastic rubber injection molding process moldsIn the process of molding and filling the mold cavity, if the filling performance of the product is not good, the pressure drop is to...
01 Aug, 2022
Type Analysis of Thermoplastic Rubbers
Thermoplastic rubber transcends the traditional boundaries of rubber and plastic in industrial production, and brings new changes to the development of the rubber industry. The emerging thermoplastic ...
22 Jul, 2022
TPV Blow Molding Guide for Thermoplastic Rubber
Thermoplastic polyolefin elastomer based on EPDM+PP, material hardness: Shore A92±3; it can be molded like thermoplastics, such as polyethylene, polypropylene, etc., by injection molding, extrusion, ...